storage battery 12V 2AH

Prostar GP2-12 sealed agm renewable energy storage battery 12V 2AH

Valve Regulated Lead Battery | 12V 2AH | Maintenance-free |Dimension: 177x35x61x67mm

SKU: GP2-12 Category:

Prostar GP2-12 sealed agm renewable energy storage battery 12V 2AH is only enough electrolyte in the mat to keep it wet, and if the battery is punctured the electrolyte will not flow out of the mats.

The storage battery or secondary battery is such a battery where electrical energy can be stored as chemical energy and this chemical energy is then converted to electrical energy as and when required. The conversion of electrical energy into chemical energy by applying external electrical source is known as charging of battery. Whereas conversion of chemical energy into electrical energy for supplying the external load is known as discharging of secondary battery.

Despite having a very low energy-to-weight ratio and a low energy-to-volume ratio, lead-acid batteries have an economically acceptable power-to-weight ratio. This feature, along with their low cost, makes the lead-acid batteries to be attractive for use in motor vehicles to provide the high current required by automobile starter motors and suitable for a number of stand-by applications.

Lead-acid batteries are composed of a Lead-dioxide cathode, a sponge metallic Lead anode and a Sulphuric acid solution electrolyte. This heavy metal element makes them toxic and improper disposal can be hazardous to the environment.

storage battery 12V 2AH


Features of Sealed Lead Acid Batteries

1. Sealed/Maintenance-free

The valve regulated spill proof construction allows trouble-free safe operation in any position. There is no need to add electrolyte, as gases generated during the charge phase are recombined in a unique “ oxygen cycle”.

Prostar sealed lead acid battery can be operated in virtually any orientation without the loss of capacity or electrolyte leakage. However, upside down operation is not recommended.

2. Long Shelf Life

A low self-discharge rate, up to approximately 3% per month, may allow storage of fully charged batteries for up to a year, depending on storage temperatures, before charging becomes critical. However, we strongly recommend that all batteries should be recharged within six months of receipt as it will enhance their long term life.

3. Design Flexibility

Same model batteries may be used in series and/or parallel to obtain choice of voltage and capacity. The same battery may be used in either cyclic or standby applications.

4. Deep Discharge Recovery

Special separators, advanced plate composition and a carefully balanced electrolyte system ensure that the battery has the ability to recover from excessively deep discharge.

5. Economical

The high watt-hour per dollar value is made possible by the materials used in a sealed lead-acid battery; they are readily available and low in cost.

6. Easy Handling

No special handling precautions or shipping containers, surface or air, are required due to the leak-proof construction.

7. Compact

Prostar batteries utilize state of the art design, high grade materials, and a carefully controlled plate-making process to provide excellent output per cell. The high energy density results in superior power/volume and power/weight ratios.

8. Low Pressure Valve Regulators

All batteries feature a series of low pressure one-way relief valves. These valves safely release any excessive accumulation of gas inside the battery and then reseal.

9. High Discharge Rate

Low internal resistance allows discharge currents of up to 10 times the rated capacity of the battery. Relatively small batteries may thus be specified in applications requiring high peak currents.

10. Rugged Construction

The high impact resistant battery case is made of nonconductive ABS plastic. The case materials impart great resistance to shock, vibration, chemicals and heat.

Battery Construction

Battery Construction



Depending on the model, batteries come either with AMP Faston type terminals made of tin plated brass, post type terminals of the same composition with threaded nut and bolt hardware, or heavy duty flag terminals made of lead alloy.


Immobilized dilute sulfuric acid: H2S04.

Leakproof Design & Operational Safety

The leak proof construction of Prostar batteries has ensured that our batteries have been approved for shipment by air.

Plates (electrodes)

Prostar utilizes the latest technology and equipment to cast grids from a lead-calcium alloy free of antimony. The small amount of calcium and tin in the grid alloy imparts strength to the plate and guarantees durability even in extensive cycle service. Lead dioxide paste is added to the grid to form the electrically active material.

Relief valve

In case of excessive gas pressure build-up inside the battery, the relief valve will open and relieve the pressure. The one-way valve

not only ensures that no air gets into the battery where the oxygen would react with the plates causing internal discharge, but also represents an important safety device in the event of excessive overcharge.

Vent release pressure is between 2-6 psi; the seal ring material is neoprene rubber.

Leakproof Design & Operational Safety

The leak proof construction of Prostar batteries has ensured that our batteries have been approved for shipment by air.


Case and lid material is ABS, high impact, resin with high resistance to chemicals and flammability. Case and cover are made of non-conductive ABS plastic.

This case has molded-in dividers for each 2 volt cell.


Prostar battery separators are made of non-woven glass fiber cloth with high heat and oxidation resistance. The material further offers superior electrolyte absorption and retaining ability, as well as excellent ion conductivity.

Case Sealing

Depending on the model the case sealing is ultrasonic, epoxy or heat

Performance Characteristics

battery performance characteristics

battery performance characteristics

Battery Applications

  • Automotive and traction applications.
  • Standby/Back-up/Emergency power for electrical installations.
  • Submarines
  • UPS (Uninterruptible Power Supplies)
  • Lighting
  • High current drain applications.
  • Sealed battery types available for use in portable equipment.
  • Grid scale energy storage

The Articles You May Like

Product Tags:  battery 12V 2AH renewable energy storage battery

    Request Product Price


    Nominal Voltage 12V
     Nominal Capacity (20 hour rate) 2.0Ah


    10 hour rate (0.19A) 1.9Ah
    5 hour rate (0.36A) 1.8Ah
    1 hour rate (1.32A) 1.32Ah
    Internal Resistance Full Charged Battery 25℃ ≤40mΩ
    Capacity affected by Temperature

    (10 hour )

    40℃ (104°F) 102%
    25℃ (77°F) 100%
    0℃ (32°F) 85%
    -15℃ (5°F) 65%

    25℃(77°F) Capacity

    after 3 month storage 90%
    after 6 month storage 80%
    after 12 month storage 62%
    Charge (Constant Voltage) 25℃(77°F) Float Initial Charging Current Less than 0.6A

    Voltage 13.6-13.8V

    Cycle Initial Charging Current Less than 0.6A

    Voltage 14.4-15.0V


    Battery Dimensions Length 177mm
    Width 35mm
    Height 61mm
    Total Height 67mm
    Box Dimensions Length 419mm
    Width 192mm
    Height 188mm
    Quantity Per Box 20 PC per box
    Net weight Per Cell 0.82kg±50g
    Net weight Per Box 16.2kg
    Gross Weight 16.7kg

    Discharge Constant Current per Cell (Amperes at 77°F25°C)

    F.V/Time 5min 10min 15min 30min 45min 1h 2h 3h 5h 8h 10h 20h
    1.60V 6.60 4.40 3.31 2.20 1.54 1.32 0.83 0.57 0.38 0.25 0.21 0.11
    1.65V 6.48 4.32 3.25 2.16 1.51 1.30 0.81 0.56 0.37 0.25 0.21 0.11
    1.70V 6.36 4.24 3.19 2.12 1.48 1.27 0.80 0.54 0.36 0.24 0.20 0.11
    1.75V 6.24 4.16 3.13 2.08 1.46 1.25 0.78 0.53 0.36 0.24 0.20 0.10
    1.80V 6.00 4.00 3.01 2.00 1.40 1.20 0.75 0.51 0.34 0.23 0.19 0.10

    Discharge Constant Power per Cell (Watts at 77°F 25°C)

    F.V/Time 5min 10min 15min 30min 45min 1h 2h 3h 5h 8h 10h 20h
    1.60V 12.71 8.47 6.37 4.24 2.96 2.54 1.59 1.09 0.73 0.49 0.40 0.21
    1.65V 12.47 8.32 6.26 4.16 2.91 2.49 1.56 1.07 0.71 0.48 0.40 0.21
    1.70V 12.24 8.16 6.14 4.08 2.86 2.45 1.53 1.05 0.70 0.47 0.39 0.20
    1.75V 12.01 8.01 6.03 4.00 2.80 2.40 1.50 1.03 0.69 0.46 0.38 0.20
    1.80V 11.55 7.70 5.79 3.85 2.70 2.31 1.44 0.99 0.66 0.44 0.37 0.19